Except for a few surface-mount technology (SMT) aluminum electrolytic capacitor types with solid electrolyte systems, an aluminum electrolytic capacitor consists of a wound capacitor element, impregnated with liquid electrolyte, connected to terminals and sealed in a can.
Forcibly inserting a capacitor into a PC board when the hole spacing doesn''t exactly match the terminal spacing will damage the lead wires or terminals, the capacitor seal and the internal connections to the element. This mechanical stress may cause sealing failure, electrolyte leakage and electrical failures such as a short circuit (non-solid).
Aluminum Electrolytic Capacitors MEC-CON At present, the organic solvent contained halogenated hydro-carbon such as Trichloroethylene, 1,1,1-Trichloroethane, and Freon are used to remove flux from circuit board. However, if general types aluminum electrolytic capacitors which seal constructions are not solvent-proof, are
An aluminum electrolytic capacitor is manufactured by impregnating the capacitor element with an electrolyte and enclosing it with an aluminum case and sealing materials. The type of terminal and sealant structure are different for each product type. Basic structures are shown in Fig. 3.
Fig. 2 Structure of aluminum electrolytic capacitor element An aluminum electrolytic capacitor is manufactured by impregnating the capacitor element with an electrolyte and enclosing it with an aluminum case and sealing materials. The type of terminal and sealant structure are different for each product type. Basic structures are shown in Fig
・Do not reuse Aluminum Electrolytic Capacitors once mounted and electrified in a unit. Reuse of the capacitors is unallowable unless they are detached from PCB for the purpose of electric measurement. ・Aluminum Electrolytic Capacitors may have recurring voltage even after discharging. Please discharge capacitors through a 1kΩ resistor
Capacitors should be stored sealed in bag until they are actually used. Once the sealed bag is cut open, all the parts should be used at one time. If not, then the remaining parts
An aluminum electrolytic capacitor is manufactured by impregnating the capacitor element with
Since each capacitor is hermetically sealed, the wet element inside impregnated with electrolyte will not be exposed to external conditions such as high pressure or vacuum. Furthermore, all electrical parameters such as impedance, leakage current, ESR and capacitance, will not be
(2) If lead wires must be formed to meet terminal board hole spacing, avoid stress on the leadwire where it enters the capacitor seal. (3) If a soldered capacitor must be removed and reinserted, avoid excessive stress to the capacitor leads. (4) Avoid touching the tip of the soldering iron to the capacitor, to prevent melting of the vinyl sleeve.
Except for a few surface-mount technology (SMT) aluminum electrolytic capacitor types with solid electrolyte systems, an aluminum electrolytic capacitor consists of a wound capacitor element, impregnated with liquid electrolyte, connected to terminals and sealed in a can.
Except for a few surface-mount technology (SMT) aluminum electrolytic capacitor types with
Fig. 2 Structure of aluminum electrolytic capacitor element An aluminum electrolytic capacitor is manufactured by impregnating the capacitor element with an electrolyte and enclosing it with an aluminum case and sealing materials. The type of terminal and sealant structure are different for each product type. Basic structures are shown in Fig
PURPOSE:To prevent that a stamped burr is formed at the flat part of a lead wire for an electrolytic capacitor and to prevent that the welded ball of the connection part of an outer lead to an internal aluminum base part becomes large-sized. CONSTITUTION:An outer lead wire 2 is inserted into and fixed to one end of a hollow aluminum wire 7; the other end of the
An aluminum electrolytic capacitor is manufactured by impregnating the capacitor element with an electrolyte and enclosing it with an aluminum case and sealing materials. The type of terminal and sealant structure are different for each product type. Basic structures are shown in Fig. 3.
Solid Aluminum Electrolytic Capacitors, Polymer, Hybrid and TCNQ Salt Solid Aluminum Electrolytic Capacitors with Conductive Polymer or TCNQ Salt Polymer Electrolytic Capacitors. Most common variant of a solid electrolyte is conductive polymer electrolyte. The aluminum oxide on an etched and formed foil is covered with an electrically very
This specification applies to polar Aluminum electrolytic capacitor (foil type) used in electronic equipment. Designed capacitor''s quality meets IEC60384. 2. Part Number System . MAN YUE ELECTRONICS COMPANY LIMITED ELECTROLYTIC CAPACITOR SPECIFICATION GF SERIES Name Specification Sheet – GF Version 01 Page 5 STANDARD MANUAL
This specification applies to polar Aluminum electrolytic capacitor (foil type) used in electronic equipment. Designed capacitor''s quality meets IEC60384. 2. Part Number System . MAN YUE ELECTRONICS CAPACITOR COMPANY LIMITED ELECTROLYTIC SPECIFICATION GT SERIES Name Specification Sheet – GT Version 01 Page 5 STANDARD MANUAL
Aluminum case, cathode lead wire, anode lead wire and circuit pattern. Auxiliary terminals of snap-in type, anode terminal, outward terminal and circuit pattern. The PVC sleeve of Aluminum Electrolytic Capacitors is not recognized as an insulator, and therefore, the standard capacitor should not be used in a place where insulation function is needed. Please consult with
(2) If lead wires must be formed to meet terminal board hole spacing, avoid stress on the
%PDF-1.5 %âãÏÓ 142 0 obj > endobj xref 142 32 0000000016 00000 n 0000001714 00000 n 0000001816 00000 n 0000002192 00000 n 0000002906 00000 n 0000003547 00000 n 0000003584 00000 n 0000003696 00000 n 0000003810 00000 n 0000003961 00000 n 0000004724 00000 n 0000005480 00000 n 0000005581 00000 n 0000006132 00000 n
Capacitors should be stored sealed in bag until they are actually used. Once the sealed bag is
gen escapes by passing through the capacitor''s rubber seal. Sealing The capacitor element is sealed into a can. While most cans are aluminum, phenolic cans are often used for motor-start capacitors. In order to release the hydrogen the seal is not hermetic and it is usually a pressure closure made by
and then wound element to be impregnated with electrolyte will be enclosed in an aluminum case. Finally sealed up tightly with end seal rubber, then finished by putting on the vinyl sleeve. 4 3 No Component Material 1 Lead Line Tinned CP wire (Pb Free) 2 Terminal Aluminum wire 3 Sealing Material Rubber 4 Al-Foil (+) Formed aluminum foil
Since each capacitor is hermetically sealed, the wet element inside impregnated with
We are deeply committed to excellence in all our endeavors.
Since we maintain control over our products, our customers can be assured of nothing but the best quality at all times.